designed & dimensioned in millimeters b do not scale from this print mpsc-xx-xx-xx-x.xx-xx-x-v-xx power pins (per end) -01, -02 vertical lead style -01: for 1.57[.062] thick pcb -02: for 3.18[.125] thick pcb plating specification -l: see table 3 -t: see table 3 option -lc: locking clip (use lc-07-tm) (see fig. 2, sht 2) -7.70 -9.70 (see table 1) tail length signal pins -01, -02 power pins (per end) -80 (4 x 20) ** = not tooled ** = not tooled ** ** * = see table 2 for available combinations * * * 10.16 .400 ref "e" ref (see table 2, sheet 2) "f" ref (see table 2, sheet 2) 4.44 (typ) .175 "a" "a" 04 01 c l 05 01 (power) c1 4.19 .165 ref "b" ref 0.38 ref .015 1.47 - 0.13 + 0.05 .058 - .005 + .002 2.00 ref (typ) .079 0.38 ref (typ) .015 0.41 .016 ref (typ) 1.88 (typ) .074 0.50 sq ref (typ) .020 38.00 1.496 (19 eq spaces @ 2.00[.079]) 1.27 .050 ref (typ) 1.00 .039 ref (typ) "j" ref (see table 2, sheet 2) 2 max sway (typ) b b b "b" "b" "c" "c" section "a"-"a" c2 c3 c5 c l c-79-xx-x c4 check bow on this surface (see note 5) 2.54 ref (typ) .100 "a" - 0.50 + 0.25 0.79 ref (typ) .031 5.08 .200 ref (typ) "c" ref 2.54 .100 section "b"-"b" mps-xx-xx.xx-v sub-c-214-xx.xx-xx-x c7 2.54 .100 6.00 .236 (3 eq spaces @ 2.00[.079]) "d" - 0.13 + 0.25 3 max sway section "c"-"c" c8 c9 c fig. 1 mpsc-01-80-01-7.70-01-x-v shown sheet of unless otherwise specified, dimensions are in millimeters. tolerances are: decimals angles .x: 0.3 [.01] 2 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: vertical mini-power w/ signal socket by: mpsc-xx-xx-xx-x.xx-xx-x-v-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing bratcher 2/16/2007 2 1 sheet scale: 1.5:1 insulator: lcp, color: black power contact: copper alloy signal contact: phos bronze f:\dwg\misc\mktg\mpsc-xx-xx-xx-x.xx-xx-x-v-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. burr allowance: 0.038[.0015] max. 3. minimum pushout force: 4.45 n [1.0 lb]. 4. parts to be packaged in trays. 5. bow allowed at .002 mm/mm [.002 in/in]. 6. minimum signal contact & -lc pullout force: 4.45 n [1.0 lb] 7. parts to be packaged in trays. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision b
b b 1.42 ref (typ) .056 1.43 - 0.13 + 0.33 .056 - .005 + .013 (2 plcs) "g" "j" 2 max sway (typ) lc-07-tm fig. 2 mpsc-01-80-01-7.70-01-x-v-lc shown (same as fig. 1, unless otherwise stated) c l c11 c10 c6 0.25 ref (typ) .010 2.16 ref .085 "g" c6 fig. 3 mpsc-02-80-02-7.70-01-x-v-lc shown (same as fig. 1, unless otherwise stated) c l 5.00 (typ) .197 "f" b c12 c1 c l "f" c1 sheet of vertical mini-power w/ signal socket by: mpsc-xx-xx-xx-x.xx-xx-x-v-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing bratcher 2/16/2007 2 2 sheet scale: 1.75:1 revision b f:\dwg\misc\mktg\mpsc-xx-xx-xx-x.xx-xx-x-v-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|